Dodge Archives - Page 2 of 3 - Inter Mountain Truck & Auto Repair

2005 Dodge Pickup
Mileage
292,038
Service Date
2/5/2021
Services Performed
Change engine oil and filter. Lube chassis. Visually inspect steering, suspension, exhaust, brakes and cooling systems. Check all fluid levels and add as necessary. Inspect condition of drive belts and hoses. Check external lighting. Reset maintenance reminder if applicable. Services re usable air filter.
Check battery condition and load capacity. Check alternator output and diode waveform. Check for system current draw. Check starter draw and cranking RPM. Noted draw after sitting for a few days. Removed all after market wiring from battery and tested all. All passed tests. Draw is intermittent. Noted Edge tuner screen is not timing out/ shutting down. Removed Edge screen and completed updates. Plugged back in and completed restart, concerns resolved.
Drain transmission and remove pan. Inspect for debris. Adjust bands if needed. Renew filter and pan gasket. Refill transmission to capacity. Road test vehicle.
Inspected and found after market intake filter housing pushing against radiator pressure relief nipple causing hose to leak. Radiator cap failed pressure test. Relocated filter to prevent leak. Installed new radiator cap. Road tested truck, able to obtain full operational temperature after adding coolant & correcting leak. Cab of truck heated fully, all HVAC functions correct.
Inspected multifunction switch for concerns. Unable to re create concerns, all functions work. Due to mileage/ time, recommend replacing multifunction switch.
Install A/C test equipment: check A/C system pressures, low, recharged. Check A/C pressure switches, relays, compressor, controls and related power and ground circuits. Found compressor connector wires separated and shorting, secured, recommend new connector harness. Check system for leaks. Check for stored HVAC fault codes. Found A/C clutch relay failed, replaced. Removed and replaced A/C wiring harness.
Installed customer supplied license plates. Drilled hole in rear for back up camera.
Removed and replaced customer supplied adjustable track bar. Adjusted and road tested.
Removed and replaced drag link and connecting tie rod end. Removed and replaced steering damper. Road tested.
Removed and replaced wiper switch. Tested all functions.
Removed rear driveline and center support bearing. Found boot for yoke worn out, cleaned all parts flipped boot over and re secured. Installed new center support bearing and re installed driveline. Road tested.
Replace both batteries. Clean battery tray. Clean cables and apply corosion inhibitor to terminals.
Lila D. gave our service a 5 star review on 2/5/2021
2008 Dodge Pickup
Mileage
120,869
Service Date
11/3/2020
Services Performed
Check condition of front and rear shocks. Found poor front and rear shocks. Removed and replaced front and rear shocks. Steering stabilizer on back order, reschedule for install.
Removed all parts to access rear axle seals. Both left and right wheel seal have slight seepage. Parking brake shoes are not contaminated. Cleaned area's and re installed all parts.
Removed failed lamp sockets. Installed new lamp sockets and tested functions.
Removed front sway bark links, installed new sway bar links. Road tested.
Scott E. gave our service a 5 star review on 11/3/2020
2007 Dodge Pickup
Mileage
110,656
Service Date
6/12/2020
Services Performed
No check engine light when inspected. Checked for codes: P0341 (stored) camshaft position sensor performance- bank 1 sensor; P0868 (stored) line pressure low; U0184 lost communication with radio; U0195 lost communication with SDARS; U0184 lost communication with radio. Tested batteries: right 786, left 870; load tested, passed all tests. Checked for 5 volts on pink/yellow wire at connector for cam- tested good. Checked for good ground at same connector- good. Recommend new cam sensor.
Removed all parts necessary to access camshaft position sensor. Removed failed sensor. Installed new camshaft position sensor. Cleared codes and road tested. No codes returned.
David S. gave our service a 5 star review on 6/12/2020
2004 Dodge Pickup
Mileage
115,659
Service Date
5/15/2020
Services Performed
Removed all tires, brake calipers, pads and rotors. Inspected wheel seal, no concerns. Inspected parking brake pads, no concerns. Installed new rotors, pads and calipers. Installed tires and road tested.
Geoff P. gave our service a 5 star review on 6/11/2020
2004 Dodge Pickup
Mileage
158,627
Service Date
4/2/2020
Services Performed
Comp
Inspected data link wiring. Found data link port unplugged. Plugged back in, screen turned on and all information loaded. Tuner gauge turned on, road tested with no concerns.
David D. gave our service a 5 star review on 4/5/2020
2007 Dodge Pickup
Mileage
166,580
Service Date
3/16/2020
Services Performed
Change engine oil and filter. Lube chassis. Visually inspect steering, suspension, exhaust, brakes and cooling systems. Check all fluid levels and add as necessary. Inspect condition of drive belts and hoses. Check external lighting. Reset maintenance reminder if applicable.
P2509 ECM/PCM power input signal intermittent; P0483 Cooling fan speed; P0513 Invalid skim key. Replace both batteries. Clean battery tray. Clean cables and apply corrosion inhibitor to terminals. Re checked for codes, none returned.
Removed fuel filter, cleaned filter housing. Installed new fuel filter. Tested for leaks.
Mark G. gave our service a 5 star review on 3/17/2020
2004 Dodge Pickup
Mileage
208,498
Service Date
12/12/2019
Services Performed
Change engine oil and filter. Lube chassis. Visually inspect steering, suspension, exhaust, brakes and cooling systems. Check all fluid levels and add as necessary. Inspect condition of drive belts and hoses. Check external lighting. Reset maintenance reminder if applicable.
Brent N. gave our service a 5 star review on 12/13/2019
2010 Dodge Pickup
Mileage
258,547
Service Date
11/4/2019
Services Performed
Change engine oil and filter. Lube chassis. Visually inspect steering, suspension, exhaust, brakes and cooling systems. Check all fluid levels and add as necessary. Inspect condition of drive belts and hoses. Check external lighting. Reset maintenance reminder if applicable.
No labor to replace valve cover gasket, Time billed for replacement of PCV Filter on cylinder head and clean excess oil
Removed failed drivers side fog lamp and replace bulb. Test for proper operation
Renew fuel filter and inspect for leaks.
Gary H. gave our service a 5 star review on 11/4/2019
2004 Dodge Pickup
Mileage
123,706
Service Date
10/18/2019
Services Performed
Change engine oil and filter. Lube chassis. Visually inspect steering, suspension, exhaust, brakes and cooling system. Check all fluid levels and add as necessary. Inspect condition of drive belts and hoses. Check all exterior lighting. Reset maintenance reminder if applicable.
Diag and advise for coolant and oil leak
THERMOSTAT &/OR GASKET – Remove & Replace – In-Line6 w/Air Cond
WATER PUMP – Remove & Replace – In-Line6
Isaiah S. gave our service a 5 star review on 10/19/2019
2007 Dodge Pickup
Mileage
83,602
Service Date
7/8/2019
Services Performed
Pulled codes and found P242F and P1451 for DPF Restriction and system performance. Truck not in regen now. Codes cleared and talked to client about regen process as he only drives 5 miles one way to work.
Mike F. gave our service a 5 star review on 7/8/2019

Dodge

We Service and Repair all Dodge cars